Precautions for the use of film blowing machine
Strictly follow the precautions for the use of the film blowing machine, which can reduce the mechanical loss and extend the service life of the machine.
1. Since electrical components may be damaged during transportation or the wire ends may fall off, you should strictly check first. In order to ensure personal safety, you must connect the ground wire when opening the organ, then turn on the power supply, and then strictly check whether the motors are running correctly at all parts, and pay attention Whether there is leakage phenomenon.
2. When installing, pay attention to adjusting the center line of the extruder head and the center of the traction roller to keep it horizontal and vertical, and not to deviate from the skewed.
3. As the outer diameter of the winding gradually increases during winding, please pay attention to the coordination of the traction speed and the winding speed, and please adjust it in time.
4. After the host is turned on, pay close attention to the operation of the host, and adjust, modify, electrical instruments and controllers in time to ensure its normal operation.
5. The main engine gearbox and traction reduction box should be refueled frequently, and the gear oil should be replaced. Please replace the new gear oil within 10 days of use for the new machine to ensure the normal operation of all rotating parts. Pay attention to refueling to prevent jamming and overheating damage. Check the tightness of each connection part to prevent the bolt from loosening.
6. The compressed air in the bubble tube should be kept in an appropriate amount, because the compressed air will leak out during the towing process, please add it in time.
7. Frequently clean and replace the filter screen in the machine head to prevent clogging, and prevent the inclusion of iron, sand, stone and other impurities in the plastic particles to avoid damage to the screw barrel.
8. It is strictly forbidden to rotate without material. When the barrel, tee, and die have not reached the required temperature, the host cannot be started.
9. When starting the main motor, start the motor first and then slowly accelerate; turn off the main motor, first decelerate and then shut down.
10. When preheating, heating should not be too long or too high to avoid clogging of the material port. The variable frequency speed regulation and drive system of the film blowing machine consists of two parts: one is the frequency converter of the extrusion main motor, and the other is the frequency converter of the traction motor. Their control is very simple, and the speed of the motor can be through the keyboard on the panel. Or connect a given potentiometer to adjust. The design of the mold (die head) is also related to the quality of the blown film, the surface finish of the spiral body and the inner wall of the mold barrel, the absolute balance of the spiral (the absolute balance of each shunt groove), the pressure of the cavity in the mold, and the pressure of the die. The extension angle, the depth (height) of the die setting section, the ratio of the die gap to the thickness of the blown film, the total height of the die, the wall thickness design of the mold barrel (heat preservation), the design of the outer heating ring (the uniform heating temperature) Distribution), etc., are the key points that must be carefully designed to blow the "perfect" film. Speed up and down time: Since plastic machinery does not need to start and brake frequently, there is no strict requirement on the speed up and down.
Article link: China Plastic Machinery Network http://www.86pla.com/Tech_news/Detail/10660.html
Related News
- What are the functions of the components of the film blowing machine?
- What is a film blowing machine
- Double-layer co-extrusion film blowing machine
- What is the reason for the poor permeability of the film blown by the PE film blowing machine
- How to maintain and repair the film blowing machine?
- Performance and use of blown film machine
- Precautions for the operation of film blowing machine
- Matters needing attention during maintenance of film blowing machine body
- New Modification of Film Blowing Machine
- Classification introduction of plastic film blowing machine
- Film blowing machine manufacturer Shantou Shuangli Machinery shares with you the methods of energy-saving transformation
- Double force film blowing machine manufacturer Shantou Shuangli Machinery tells you the process flow of film blowing
- Two parts of the energy-saving transformation of the film blowing machine are introduced, Shantou Zhongli Machinery will share with you
- Shuangli Machinery, a film blowing unit manufacturer, tells you the experience of choosing a film blowing machine
- Shantou Film Blowing Machine tells you what are the reasons and maintenance methods for the damage of the tie rod of the convenient bag film blowing machine?
- What are the reasons and troubleshooting methods for the temperature deviation of the hydraulic oil of the film blowing machine?
- How to compare the quality of high-speed film blowing machine
- Two parts of the energy-saving transformation of the film blowing machine are introduced, Shantou Zhongli Machinery will share with you
- Film blowing unit analyzes the distinction of film blowing machine for you, Shantou Zhongli shares with you
- Zhongli film blowing machine manufacturer Shantou Zhongli will explain to you what are the operating steps