Master the working principle of PE film blowing machine to produce high-quality PE film
PE film blowing machineIt is familiar to the majority of manufacturers and film manufacturers, but at the same time, many manufacturers know very little about his working principle and film making technology. Many manufacturers always cannot master the technology when they use the PE film blowing machine to make PE film. The film is not stable. It is clear that high-quality PE raw materials are used, but the blown PE film is always transparent, elastic, and uneven. These are all affected by factors such as temperature, wind, and flow during the hand blowing process.
The PE film blowing process includes heating, traction, and winding processes, and the heating is divided into 5 zones. The first, second, and third zones are heating zones (preheating), and the temperature gradually rises, which is very important for temperature control. If the temperature is too low, it is not easy to discharge, and if the temperature is too high, it is easy to modify and transform. Take the 80 blown film machine as an example, the lower zone is about 170℃, and the latter two zones are higher. The fourth zone (three-way zone) is also used as a heating zone. There is mainly a filter screen that can filter and prevent impurities in the raw materials from entering the fifth zone. The transparency and smoothness of the blown PE film are determined by the filter screen. Larger meshes (smaller meshes) filter more finely and make the film smoother, but too small meshes will cause the retention of raw materials. The five-zone discharging zone is very important. The temperature and flow rate need to be strictly controlled. The suitability of the entire heating process should be controlled according to the discharging mouth. Too high or low will affect the formation of the film. The five zones are equipped with The blower accelerates the formation of the film, and the unevenness of the film thickness must be adjusted by the film head thread.
The accessory of the traction zone is an air pump, which is filled with air through the blowing hole of the film head, and the film is linearly upward, which is used to control the size of the film. Then go through the film stabilizer to "stabilize the film". The thickness of the film can be controlled by adjusting the host and traction speed (the faster the host speed, the faster the feeding speed, the thicker the film, and vice versa) This is the most important link.
By mastering the working principle, you can produce high-quality PE film.
Previous: Shuangli Machinery tells you how to improve the film blowing technology of the film blowing machine
Related News
- What are the functions of the components of the film blowing machine?
- What is a film blowing machine
- Double-layer co-extrusion film blowing machine
- What is the reason for the poor permeability of the film blown by the PE film blowing machine
- How to maintain and repair the film blowing machine?
- Performance and use of blown film machine
- Precautions for the operation of film blowing machine
- Matters needing attention during maintenance of film blowing machine body
- New Modification of Film Blowing Machine
- Classification introduction of plastic film blowing machine
- Shuangli Machinery tells you how to improve the film blowing technology of the film blowing machine
- Shantou Shuangli Machinery Factory fully supports the 2017 China Tongcheng (Xindu) Plastic Machinery Fair
- The double force film blowing machine tells you what to pay attention to during the use of the film blowing machine
- Shantou Shuangli Plastic Machinery gained a lot in the "2017 China Tongcheng Plastic Packaging Machinery Exhibition"
- The advantages of the film blowing machine after the transformation of the three crystal inverter
- Shuangli Machinery wishes everyone a happy Dragon Boat Festival
- Shantou Shuangli Machinery Factory-October 12-14, 2017, once again attended the Chengdu Rubber Plastics and Packaging Exhibition
- Shantou Film Blowing Machine participated in the 11th China (Chengdu) Rubber Plastics and Packaging Industry Exhibition
- Shuangli Machinery shares with you the purpose of developing a co-extrusion blown film machine
- Congratulations to the 11th China (Chengdu) Rubber Plastics and Packaging Industry of Shantou Film Blowing Machine has reached cooperation with many customers